菜单

外部传感器

燃气是的不
压力是的不
温度是的不
连接技术是的不
流速是的不
种类EDS1EDS2
每页条目
1 - 20 / 63
EDS2-V flow meter 1-42l/min 5%
新的
EDS2-V flow meter 1-42l/min 5%Digital flow meter to connect to smart memo. Measurement data are automatically transferred and used, for example, for the pressure drop test according to German DVGW guideline W 400-2. Can be used for the following drain volumes in water pressure tests (e.g. W 400-2/W 101/EN 805): min. 32 ml max. 84 litres Sensor type: flow meter Measuring range: 1-42l/min. Accuracy: 5% of MW. Operating temperature: 0°C to +70 °C Max. pressure: 25 bar Connection: inlet nipple series 5020, outlet Geka coupling Instructions for use: For proper measurement results, the sensor must be rinsed with water before the test is carried out! During water pressure tests with an expected drain volumes < 500 ml a flow reducer (article number 402125) should be used!
EDS2 automatic drain module
新的
EDS2 automatic drain moduleOptional module for the smart memo to automatically perform pressure drop tests and pressure reduction during water pressure tests. The EDS2 automatic drain is connected directly to the test head HANS with an integrated hose piece. On the outlet side, a suitable EDS2-V must be connected to the EDS2 automatic pressure release. The automatic pressure release only works in combination with an EDS2-V for digital recording of the water volume! The automatic drain is currently supported in the following processes: W 400-2: contraction procedure, accelerated standard procedure, standard procedure, infuence-minimized standard procedure W 101: contraction procedure, standard procedure EN 805: contraction procedure, standard procedure Mechanical connections: - hose connection with nipple series 5000 on the inlet side - on the outlet side coupling Series 5000 - bracket for fixing to the test stand pipe Electrical connections: - 1x socket B11 on the inlet side (power supply via smart memo) - on the outlet side, 3x connector B11 for direct connection of further EDS2 sensors (no additional T-pieces necessary) max. pressure 30 bar max. flow 75 liters/minute Note on use: when carrying out water pressure tests with an expected discharge volume of < 500 ml, a flow reducer (article number 402125) should always be used!
Temperature sensor ground stake EDS2-T 0,1K
新的
Temperature sensor ground stake EDS2-T 0,1KMeasuring range: 0°C to 40 °C Measuring range resolution: up to 0.01 °C Accuracy: 0.1 °C Total length: 1.04 m Material: stainless steel This sensor is suitable for measuring temperature during pressure tests in accordance with DVGW W 400-2 (2022).
EDS2-V flow meter 4-160l/min 5%
新的
EDS2-V flow meter 4-160l/min 5%Digital flow meter to connect to smart memo. Measurement data are automatically transferred and used, for example, for the pressure drop test according to German DVGW guideline W 400-2. Can be used for the following discharge volumes in water pressure tests (e.g. W 400-2/W 101/ EN 805): min. 8 litres max. 320 litres Sensor type: flow meter Measuring range: 4-160l/min. Accuracy: 5% of MW. Operating temperature: 0°C to +70 °C Max. pressure: 25 bar Connection: inlet nipple series 5020, outlet Geka coupling Instructions for use: For proper measurement results, the sensor must be rinsed with water before the test is carried out!
Temperature sensor contact element EDS2-T 0,1K
新的
Temperature sensor contact element EDS2-T 0,1KMeasuring range: 0°C to 40 °C Measuring range resolution: up to 0.01 °C Accuracy: 0.1 °C Docking element with an elastic belt for fixing to the pipe, up to approx. OD 500. Material: synthetic material (housing), aluminum (contact face) This sensor can be used for the measurement of temperatures for pressure tests according to W 400-2 (2022).
EDS2 level probe
新的
EDS2 level probeExternal sensor can be connected to the measuring device, integrated connection cable 0.5 metres Sensor type: Level probe Measuring principle: Pressure measurement Measuring range: 300 mm Measuring accuracy: 0.3 mm at 20°C Resolution: 0.1 mm Operating temperature: +3 °C to +40 °C Maximum immersion depth: 500 mm
Tripod level probe
新的
Tripod level probeCompact, portable tripod with pre-assembled holder for an EDS2 level probe. - Integrated bubble level for optimal alignment of the tripod - Extendable, lockable tripod legs for use with small (DN100) to very large manhole openings (DN1000) - Extension tubes with screw connection for easy insertion of the level probe - Integrated B11 T-piece for connecting the level probe and the connection cable of the smart memo , optional connection of the EDS2 automatic level control possible
smart level control
新的
smart level controlOptional module for water testing on sewage manholes/pipes in accordance with EN 1610 in conjunction with the EDS2 level probe and smart memo. In the event of a drop in level during the test, the smart level control automatically tops up the test area with water to maintain the initial level. The amount of water added is automatically measured and the measured value is sent to the smart memo. The smart level control is connected to the smart memo via an additional B11 termination cable. A container for use as a water reservoir should be positioned at least 0.5 metres above the smart level control and connected to it via a hose. Technical data: Operating temperature: +5°C to 40°C Max. flow rate: 20 l/h (with sufficient inlet pressure, e.g. 50 cm water gauge) Measuring range: 0.3 l/min - 6 l/min Accuracy: +-5% (at 0.3-3 l/min) Max. inlet pressure: 0.1 bar (1 metre water column) Mechanical connections: nipple (Series 21) on the inlet side, coupling (Series 21) on the outlet side Electrical connections: 1x socket B11 (power supply via smart memo) Connecting hoses are included in the scope of delivery
External pressure sensor EDS2-P 10 bar 0.1% DAkkS
External pressure sensor EDS2-P 10 bar 0.1% DAkkSincl. DAkkS calibration certificate (initial certification according to G 469) can be used on the measuring device via connection cable Sensor type: Absolute pressure sensor Measuring range: 0 to 10 bar above atmospheric pressure Measuring accuracy: < 0.1% of full scale Operating temperature: -20 °C to +70 °C Max. Pressure 15 bar Connection: external thread G 1/4".
Pressure sensor EDS2-P 25 bar 0,1%
Pressure sensor EDS2-P 25 bar 0,1%deployable to measurement device via connecting cable sensor type: absolute pressure sensor measurement range: 0 to 25 bar above atmospheric pressure measurement accuracy: < 0,1 % of full scale operating temperature: -20 °C bis +70 °C maximum pressure: 40 bar connection: external thread G 1/4"
Connecting cable B11 5m
Connecting cable B11 5mfor external digital sensors (EDS2), length: 5 m connection to smart memo
T-piece B11
T-piece B11T-connection piece B11 bayonet coupling 11 mm
Pressure Sensor EDS2-P 15bar 0,01% 0-40°C
Pressure Sensor EDS2-P 15bar 0,01% 0-40°Capplicable at the measuring device via connecting cable sensor type: absolute pressure sensor measurement range: 0 to 15 bar above atmospheric pressure measurement accuracy: < 0,02 % of full scale measurement precision: < 0,01% of full scale at 0-40°C resolution: 1 mbar operating temperature: -20 °C bis +70 °C maximum pressure: 50 bar connection: external thread G 1/4"
External pressure sensor EDS2-P 10 bar 0,1% 0-40 °C incl. DAkkS
External pressure sensor EDS2-P 10 bar 0,1% 0-40 °C incl. DAkkScan be used with the measuring device via connection cable incl. DAkkS calibration certificate (initial certification) Sensor type: absolute pressure sensor Measuring range: 0 to 10 bar above atmospheric pressure Measuring accuracy: < 0.1% of final value at 0 - 40°C Operating temperature: -20 °C to +70 °C Max. pressure 15 bar Connection: outer thread G 1/4"
Temperature sensor contact element EDS2-T 0,1K DAkkS
Temperature sensor contact element EDS2-T 0,1K DAkkS including DAkkS calibration certificate Measuring range: 0°C to 40 °C Measuring range resolution: up to 0.01 °C Accuracy: 0.1 °C Docking element with an elastic belt for fixing to the pipe, up to approx. OD 500. Material: synthetic material (housing), aluminum (contact face) This sensor is suitable for measuring temperatures during pressure tests in accordance with DVGW G 469 C3.
Pressure sensor EDS2-P 10 bar 0,1%
Pressure sensor EDS2-P 10 bar 0,1%deployable to measurement device via connecting cable sensor type: absolute pressure sensor measurement range: 0 to 10 bar above atmospheric pressure measurement accuracy: < 0,1 % of full scale operating temperature: -20 °C to +70 °C maximum pressure: 15 bar connection: external thread G 1/4"
Temperature sensor ground stake EDS2-T Measuring range: -20°C to 70 °C
Temperature sensor ground stake EDS2-T Measuring range: -20°C to 70 °CTemperature sensor ground stake EDS2-T Measuring range: -20°C to 70 °C Measuring range resolution: up to 0,01 °C Accuracy: 0,25 °C Total length: 1,04 m Material: stainless steel This sensor can be used for the measurement of temperatures for pressure tests according to W 400-2 and G 469 B3. He cannot get an initial certification according to G 469 C3 (high precision pressure test procedure).
Connecting cable B11 or extension cable B11, 1m
Connecting cable B11 or extension cable B11, 1mto connect external digital sensors (EDS2) with smart memo
Handheld sensor gas detection GasTest delta3
Handheld sensor gas detection GasTest delta3with integrated calibration data and vibration alarm deployable with every GasTest delta3
External pressure sensor EDS2-P 1,6bar 0,25%
External pressure sensor EDS2-P 1,6bar 0,25%Pressure sensor EDS2-P 1,6 bar 0,25% can be used on the measuring device via connecting cable sensor type: absolute pressure sensor measurement range: 0 to 1,6 bar above atmospheric pressure measurement accuracy: < 0,25 % FS for 0-400 mbar < 0,25 % FS for 0-1600 mbar operating temperature: -20 °C bis +70 °C maximum pressure: 2 bar connection: external thread G 1/4"
每页条目
1 - 20 / 63
keyboard_arrow_up